This document gives guidelines to set up, run, and postprocess correct
simulations with the finite element method. It is not an introduction to the
method itself, but rather a list of things to check and possible mistakes to
watch out for when doing a finite element simulation.

more |
pdf
| html
ComputerPapers:
How to get meaningful and correct results from your finite element model. https://t.co/UNfZ3s1qNw

None.

None.

Sample Sizes : None.

Authors: 1

Total Words: 8411

Unqiue Words: 2359

This paper presents three distributed techniques to find a sparse solution of
the underdetermined linear problem $\textbf{g}=\textbf{Hu}$ with a norm-1
regularization, based on the Alternating Direction Method of Multipliers
(ADMM). These techniques divide the matrix $\textbf{H}$ in submatrices by rows,
columns, or both rows and columns, leading to the so-called consensus-based
ADMM, sectioning-based ADMM, and consensus and sectioning-based ADMM,
respectively. These techniques are applied particularly for millimeter-wave
imaging through the use of a Compressive Reflector Antenna (CRA). The CRA is a
hardware designed to increase the sensing capacity of an imaging system and
reduce the mutual information among measurements, allowing an effective imaging
of sparse targets with the use of Compressive Sensing (CS) techniques.
Consensus-based ADMM has been proved to accelerate the imaging process and
sectioning-based ADMM has shown to highly reduce the amount of information to
be exchange among the computational nodes. In this paper,...

more |
pdf
| html
None.

None.

Sample Sizes : None.

Authors: 4

Total Words: 9103

Unqiue Words: 2171

Many methodologies have been proposed to quickly identify among a very large
number of flight conditions and maneuvers (i.e., steady, quasi-steady and
unsteady loads cases) the ones which give the worst values for structural
sizing (e.g., bending moments, shear forces, torques,...). All of these methods
use both the simulation model of the aircraft under development and efficient
algorithms to find out the critical points of the flight envelope. At the
preliminary structural design phases detailed models are not available and
airframe's loads are estimated by empirical relationships or engineering
judgments. These approximations can induce load uncertainties and may lead to
expensive redesign activities through the upcoming detailed sizing process. In
the context of preliminary design phase for a weight aircraft variant without
geometric change, to overcome this likely drawback, we propose a method based
on the huge and reliable database of an initial aircraft from which the weight
variant belongs. More precisely, from the load...

more |
pdf
| html
None.

None.

Sample Sizes : None.

Authors: 4

Total Words: 3051

Unqiue Words: 1166

This paper addresses uncertainties arising in the nano-scale fabrication of
optical devices. The stochastic collocation method is used to propagate
uncertainties in material and geometry to the scattering parameters of the
system. A dimension-adaptive scheme based on Leja nodes is employed to reduce
the computational complexity. By combining the Leja adaptive algorithm with an
adjoint-based error indicator, an even smaller complexity is obtained. The
scheme's efficiency is demonstrated by numerical results for an optical grating
coupler. For this model problem, the adaptive strategy allows to compute
statistical moments, probabilities and global sensitivity indices, taking into
account a moderately high number of uncertain input parameters. In particular,
it is found that geometric sensitivities outweigh sensitivities with respect to
material parameters for the considered setting.

more |
pdf
| html
None.

None.

Sample Sizes : None.

Authors: 4

Total Words: 13904

Unqiue Words: 3571

This paper presents a structure-exploiting nonlinear model reduction method
for systems with general nonlinearities. First, the nonlinear model is lifted
to a model with more structure via variable transformations and the
introduction of auxiliary variables. The lifted model is equivalent to the
original model---it uses a change of variables, but introduces no
approximations. When discretized, the lifted model yields a polynomial system
of either ordinary differential equations or differential algebraic equations,
depending on the problem and lifting transformation. Proper orthogonal
decomposition (POD) is applied to the lifted models, yielding a reduced-order
model for which all reduced-order operators can be pre-computed. Thus, a key
benefit of the approach is that there is no need for additional approximations
of nonlinear terms, in contrast with existing nonlinear model reduction methods
requiring sparse sampling or hyper-reduction. Application of the lifting and
POD model reduction to the FitzHugh-Nagumo benchmark problem and...

more |
pdf
| html
None.

None.

Sample Sizes : None.

Authors: 2

Total Words: 9578

Unqiue Words: 2358

In this study, in order to reduce the local high temperature of the platform
in inertial navigation system (PINS), a pin-fin heat sink with staggered
arrangement is designed. To reduce the dimension of the inputs and improve the
efficiency of optimization, a feasible global sensitivity analysis (GSA) based
on Kriging-High Dimensional Model Representation with DIviding RECTangles
sampling strategy (DIRECT-KG-HDMR) is proposed. Compared with other GSA
methods, the proposed method can indicate the effects of the structural and the
material parameters on the maximum temperature at the bottom of the heat sink
by using both sensitivity and coupling coefficients. From the results of GSA,
it can be found that the structural parameters have greater effects on thermal
performance than the material ones. Moreover, the coupling intensities between
the structural and material parameters are weak. Therefore, the structural
parameters are selected to optimize the thermal performance of the heat sink,
and several popular optimization algorithms...

more |
pdf
| html
ComputerPapers:
Design of pin-fin heat sink for the platform inertial navigation system by surrogate assisted techniques. https://t.co/hZrg1FeE2H

None.

None.

Sample Sizes : None.

Authors: 5

Total Words: 10815

Unqiue Words: 2766

A novel method for complex fluid-structure interaction (FSI) involving large
structural deformation and motion is proposed. The new approach is based on a
hybrid fluid formulation that combines the advantages of purely Eulerian
(fixed-grid) and Arbitrary-Lagrangian-Eulerian (ALE moving mesh) formulations
in the context of FSI. The structure - as commonly given in Lagrangian
description - is surrounded by a fine resolved layer of fluid elements based on
an ALE-framework. This ALE-fluid patch, which is embedded in an Eulerian
background fluid domain, follows the deformation and motion of the structural
interface. This approximation technique is not limited to Finite Element
Methods, but can can also be realized within other frameworks like Finite
Volume or Discontinuous Galerkin Methods. In this work, the surface coupling
between the two disjoint fluid subdomains is imposed weakly using a stabilized
Nitsche's technique in a Cut Finite Element Method (CutFEM) framework. At the
fluid-solid interface, standard weak coupling of...

more |
pdf
| html
ComputerPapers:
A monolithic approach to fluid-structure interaction based on a hybrid Eulerian-ALE fluid domain decomposition involving cut elements. https://t.co/7TVHb4pdJQ

None.

None.

Sample Sizes : None.

Authors: 3

Total Words: 15642

Unqiue Words: 3391

We present the AMPS algorithm, a finite element solution method that combines
principal submatrix updates and Schur complement techniques, well-suited for
interactive simulations of deformation and cutting of finite element meshes.
Our approach features real-time solutions to the updated stiffness matrix
systems to account for interactive changes in mesh connectivity and boundary
conditions. Updates are accomplished by an augmented matrix formulation of the
stiffness equations to maintain its consistency with changes to the underlying
model without refactorization at each timestep. As changes accumulate over
multiple simulation timesteps, the augmented solution algorithm enables tens or
hundreds of updates per second. Acceleration schemes that exploit sparsity,
memoization and parallelization lead to the updates being computed in
real-time. The complexity analysis and experimental results for this method
demonstrate that it scales linearly with the problem size. Results for cutting
and deformation of 3D elastic models are reported...

more |
pdf
| html
arxiv_csgr:
AMPS: A Real-time Mesh Cutting Algorithm for Surgical Simulations https://t.co/gFbAgVNA2T

arxiv_csgr:
AMPS: A Real-time Mesh Cutting Algorithm for Surgical Simulations https://t.co/gFbAgVNA2T

arxiv_csgr:
AMPS: A Real-time Mesh Cutting Algorithm for Surgical Simulations https://t.co/gFbAgVNA2T

arxiv_csgr:
AMPS: A Real-time Mesh Cutting Algorithm for Surgical Simulations https://t.co/gFbAgW5aUr

ComputerPapers:
AMPS: A Real-time Mesh Cutting Algorithm for Surgical Simulations. https://t.co/YS9n3jfjHC

None.

None.

Sample Sizes : None.

Authors: 3

Total Words: 7748

Unqiue Words: 2052

In this paper, first we present the variational formulation for a second
strain gradient Euler-Bernoulli beam theory for the first time. The governing
equation and associated classical and non-classical boundary conditions are
obtained. Later, we propose a novel and efficient differential quadrature
element based on Lagrange interpolation to solve the eight order partial
differential equation associated with the second strain gradient
Euler-Bernoulli beam theory. The second strain gradient theory has
displacement, slope, curvature and triple displacement derivative as degrees of
freedom. A generalize scheme is proposed herein to implement these
multi-degrees of freedom in a simplified and efficient way. The proposed
element is based on the strong form of governing equation and has displacement
as the only degree of freedom in the domain, whereas, at the boundaries it has
displacement, slope, curvature and triple derivative of displacement. A novel
DQ framework is presented to incorporate the classical and non-classical
boundary...

more |
pdf
| html
None.

None.

None.

Sample Sizes : [5]

Authors: 2

Total Words: 9479

Unqiue Words: 2579

Concerns about system adequacy have led to the establishment of capacity
mechanisms in a number of regulatory areas. Against this background, it is
essential to accurately quantify the contribution to security of supply that
results from interconnectors to neighbouring systems. This paper introduces a
definition of capacity value for interconnection between two systems in the
form of a capacity allocation curve. Four power flow policies are proposed to
encompass the full range of possible market outcomes that may affect the
capacity value. A convolution-based method is presented to efficiently compute
and compare capacity allocation curves, and it is applied to a model system
that is inspired by Great Britain's interconnection with the continental
Europe. The results indicate areas of interest for the coordination of capacity
mechanisms.

more |
pdf
| html
None.

ComputerPapers:
Capacity Value of Interconnection Between Two Systems. https://t.co/RcaBGTHScJ

None.

None.

Sample Sizes : None.

Authors: 3

Total Words: 4289

Unqiue Words: 1494

Assert is a website where the best academic papers on arXiv (computer science, math, physics), bioRxiv (biology), BITSS (reproducibility), EarthArXiv (earth science), engrXiv (engineering), LawArXiv (law), PsyArXiv (psychology), SocArXiv (social science), and SportRxiv (sport research) bubble to the top each day.

Papers are scored (in real-time) based on how verifiable they are (as determined by their Github repos) and how interesting they are (based on Twitter).

To see top papers, follow us on twitter @assertpub_ (arXiv), @assert_pub (bioRxiv), and @assertpub_dev (everything else).

To see beautiful figures extracted from papers, follow us on Instagram.

*Tracking 57,756 papers.*

Sort results based on if they are interesting or reproducible.

Interesting

Reproducible